⚙️ Jam Clearing · Reset · Leak Repair · Replacement
Garbage Disposal Repair in New London, TX — Jammed, Humming, Leaking? We Fix It
Your disposal hums but won't spin — the impeller plate is jammed. It's completely silent when you flip the switch — the thermal overload protector has tripped or the motor has failed. Water drips from the sink collar — the sink mounting gasket has deteriorated. Each of these is a different diagnosis, and each has a different solution. Masters Plumbing Service's techs in New London, TX arrive with the jamming tools, reset wrench, and replacement units to resolve any disposal failure same visit.
Jam Clearing & ResetInSinkErator, Moen, Waste KingSink Collar Leak RepairSame-Day Replacement Units
Why Call Masters Plumbing Service for Disposal Work
How Masters Plumbing Service Approaches Garbage Disposal Repair in New London
Garbage disposal failures have specific, diagnosable causes. Our techs don't just swap units — they identify what failed and whether repair or replacement is the right call for your situation.
🔎
Symptom-Specific Diagnosis
A disposal that hums but won't spin almost always just needs the jam cleared with an Allen wrench at the center socket and the reset button pressed — a 5-minute fix that doesn't require a new unit.
🏷️
All Major Brands Serviced
InSinkErator models use a 1/4-inch Allen wrench at the center bottom; Waste King models use a broom-handle approach at the top. Knowing which you have before arriving saves time and prevents the wrong tool damaging the motor shaft.
💲
Repair vs. Replace — Honest Guidance
We give you the actual cost comparison. If clearing the jam and pressing the reset button fixes it, that's what we do. If the motor has failed, we show you the replacement options and install same-day.
🔧
Full Plumbing Integration Check
A disposal isn't an isolated appliance — it connects to the sink drain, the dishwasher drain (if present), and the drain arm leading to the p-trap. We inspect the full connection set during any disposal call: drain arm slope, dishwasher drain knockout (if a dishwasher is being added), and p-trap connection integrity.
Our Services
Every Garbage Disposal Repair Issue We Handle in New London, TX
From a simple jam clear to a full replacement with drain reconnection, here's how we handle each garbage disposal scenario in New London, TX.
Jammed
Jam Clearing & Reset
If the jam-clearing wrench won't budge the impeller, the motor shaft may be seized rather than just stuck from debris — we distinguish between the two before recommending replacement.
Won't Start
Reset & Electrical Diagnosis
If power is confirmed at the disposal and it still won't start after a reset, the motor is failed. We then move to the replacement conversation with honest cost comparison.
Leaking
Sink Collar & Connection Leak Repair
We identify the leak source before recommending any repair. A sink collar re-seal is a 30-minute job. A unit with a cracked body has no cost-effective repair and warrants replacement.
Noisy
Noise Diagnosis & Repair
If the turntable bearing has failed — indicated by a loud rumbling throughout operation rather than specific impact sounds — that's an internal motor wear failure that warrants replacement.
Draining
Slow Drain & Drain Line Clearing
A disposal that grinds normally but drains slowly has a blockage in the drain arm or p-trap — not an internal disposal problem. Food particles and grease accumulate in the short drain arm between the disposal outlet and the p-trap. We disconnect and clean the drain arm, clear any p-trap buildup, and reinstall with clean connections.
Replacement
Full Disposal Replacement
When the motor has failed, the unit body is cracked, or the existing unit is underpowered for the household's use pattern, we replace the disposal with a new unit matched to the sink drain configuration. We carry 1/2 HP, 3/4 HP, and 1 HP units from InSinkErator and other major brands on our trucks for same-day installation.
Our Garbage Disposal Repair Diagnosis & Repair Workflow in New London
No guesswork — we diagnose before we quote, and quote before we start.
1
Describe the Symptom — We Prep Accordingly
Hums but won't spin, completely silent, grinding noise, leaking, or slow to drain — each symptom tells our dispatcher which tools and possible replacement units to have on the truck. Knowing the disposal brand is a plus but not required.
2
On-Site Diagnosis — Specific, Fast
For leaks, we dry the area completely and run a short test cycle to confirm exactly which connection is dripping.
3
Flat-Rate Quote — Repair or Replace
You decide. We don't upsell replacement when repair is the right answer, and we don't push a cheap repair that won't hold on a unit that's genuinely at end of life.
4
Repair or Install — Test Everything Before Leaving
We leave the cabinet dry and the disposal running quietly. If a dishwasher drain hose was involved, we run a dishwasher cycle to verify no backup occurs.
Customer Reviews
What New London Homeowners Say About Our Disposal Repairs
★★★★★
The disposal under our kitchen sink was 12 years old and started leaking from the bottom — which the tech explained is always an internal seal failure, not a repairable condition. He had a replacement 3/4 HP InSinkErator on his truck, installed it in about 45 minutes, and the kitchen is back to normal. Old unit got pulled, new unit tested clean, no leaks at any connection.
— E. Park, New London
★★★★★
Disposal making a loud rattling noise but still grinding. Tech took out a bottle cap that had gotten past the splash guard and was spinning around the grinding chamber. Cleaned out the chamber, confirmed the impeller wasn't damaged, tested for smooth operation. Twenty-minute visit, everything working perfectly.
— J. & L. Maher, New London, TX
★★★★★
Disposal leaking from the sink collar area. Previous owner had installed it with silicone instead of plumber's putty at the flange — silicone doesn't hold the mounting pressure correctly and had separated. Tech re-seated the flange with putty, re-tightened the mounting ring, and the leak stopped. Tested with a full minute of running water. All clear.
— Y. Okonkwo, New London, TX
Common Questions
Disposal Questions We Answer Every Day in New London
If the impeller won't free with the Allen wrench — or frees but jams again within days — the disposal may have internal damage (chipped impeller, damaged shredder ring) or a bearing that's beginning to seize. We diagnose this on-site and tell you whether repair or replacement is appropriate.
Replacement makes more sense when: the motor has completely failed (no hum, power confirmed, reset button doesn't help), the unit body is cracked and leaking from the bottom, the grinding chamber is heavily corroded or chipped, or the unit is over 10 years old with multiple issues. A new 1/2 HP disposal costs significantly less than the labor of rebuilding an old motor that will likely fail again.
The items that create the most disposal problems in New London, TX homes: large bones (chicken bones and small fish bones are fine; large beef and pork bones are not), fibrous vegetables (celery, artichoke leaves, asparagus — the fibers wrap around the impeller shaft), starchy foods in large quantities (pasta, rice, and potato peels expand with water and can pack the drain arm), and fats, oils, and grease in significant amounts (they resolidify in the drain arm, not in the grinding chamber).
The inside of the grinding chamber and the underside of the rubber splash guard accumulate food residue that standard dish soap doesn't reach. The most effective cleaning method: disconnect the disposal and clean under the splash guard's rim with a brush and dish soap, then freeze a tray of white vinegar and citric acid solution into ice cubes and run them through the disposal with cold water running.
If your disposal is in the 8–12 year range and showing signs of age — slower grinding speed, increased noise, intermittent jamming — proactive replacement before a full motor failure is often a smoother and cheaper experience than waiting for an emergency.
Technically, a disposal replacement is a combined electrical and plumbing task — most homeowners can manage it, but there are a few specific failure points that catch DIY installers: forgetting to remove the dishwasher drain knockout plug (which blocks dishwasher drainage completely), improper drain arm slope (disposal drain arm should slope down toward the p-trap), and loose wiring connections at the junction box that vibrate loose over months.
Service Area
Serving New London and the Surrounding New London, TX Region
Our trucks carry replacement disposal units in common horsepower ratings for same-day installation when the motor has failed.
